Designed to blow in multiple micro ducts or single large size cables into ducts with a dia. of 32 up to 50 mm. It is suitable for air- and water blowing. The drive chains are propelled by two low-wear and low-noise hydraulic motors which enable for- and backward movement of the cable.
|max. speed:||60 m/min|
|required air flow||10 m³/min|
|required air pressure:||12 bar|
|Control unit and Power Pack||(125 bar / 15 l/min) essential!|
Hydraulic Control Unit Order No. 111.420.00
With the control unit pressure and speed are regulated. The chains of the particular injection system are set in motion by the lever. The Power Pack is required for Bagela Powerflow, Multiflow und Miniflow.
Blowing Junction Block for micro ducts Order No. 111.282.00
Multiple micro ducts can be injected into protective ducts of 32, 40 and 50 mm dia. by air.
Cable guide „flex“ for single cable
It is to be inserted in the Blowing junction block.
|Order No.||Dia. Cable|
|111.235.10||8 - 12 mm|
|111.236.10||13 - 17 mm|
|111.237.10||18 - 22 mm|
|111.238.10||23 - 27 mm|
Nylon-Applicator for micro ducts Order No. 111.285.00
This applicator assistance for micro duct is fastened to the multi-flow and bundles the different pipes. The number of holes can vary. Please specify this when ordering.
Sealing for micro ducts, 7 pieces
The sealing is for the use of the blowing junction block with micro ducts. Many different combinations are possible regarding size and number of holes to micro ducts. Please specify when ordering.
|111.290.00||Sealing for micro ducts - 1 hole|
|111.291.00||Sealing for micro ducts - 13 holes|
|111.292.00||Sealing for micro ducts - 15 holes|
|111.293.00||Sealing for micro ducts - 5 holes|
|111.294.00||Sealing for micro ducts - 7 holes|
|111.294.10||plug for a 10mm sealing|
Odometer Order No. 111.240.00
The measuring system can be hinged onto the Powerflow or Multiflow as an additional unit. The length corresponding to the forward and backward movements is indicated and saved. The data could be transferred to the EPD system. Measuring range 0- 9999 m
Plug for micro ducts
The plug is equipped with a o-ring for 100% sealing. It is easy to mount with self cutting thread. It is available in other sizes. Please specify when ordering.
|Order No.||Product name|
|111.296.00||Plug for 7 mm micro duct|
|111.297.00||Plug for 10 mm micro duct|
|111.298.10||Plug for 12 mm micro duct|
Sealing unit with manometer Order No. 111.261.00
Laterally of the drum is the inner end of the duct where this unit is to be inserted and remain fixed during the injection procedure. A pressure loss will become visible at the manometer immediately.
Overpressure testing unit Order No. 111.260.00
facilitates this procedure and shortens the temporal expenditure to a minimum. A pressure loss will become visible at the manometer immediately. (The connecting hoses to 111.261.00 are included)
Guidance unit for micro ducts Order No. 111.262.00
The guidance unit is to be positioned between the micro duct drums and the Multiflow. It ensures a regular uncoiling of the ducts.
Additional acceptance for micro duct drums Order No. 028.328.02
This acceptance fits in all trailers of the series BKT 18 up to BKT 27
Micro Pipe Pulling Unit
Each strand has a tensile load of max. 300 kg.
Attention: Please follow the tensile load limit restrictions of the appropriate micro pipe.
The single strands are to be assembled, please make your choice.
|Order No.||Outer dia.
|111.295.11||1 x 7||1||40|
|111.295.12||1 x 7||1||50|
|111.295.13||1 x 7||1||60|
|111.295.14||1 x 7||1||70|
|111.295.21||1 x 10||1||40|
|111.295.22||1 x 10||1||50|
|111.295.23||1 x 10||1||60|
|111.295.24||1 x 10||1||70|
|111.295.31||1 x 12||1||40|
|111.295.32||1 x 12||1||50|
|111.295.33||1 x 12||1||60|
|111.295.34||1 x 12||1||70|
|111.295.41||1 x 14||2||40|
|111.295.42||1 x 14||2||50|
|111.295.43||1 x 14||2||60|
|111.295.44||1 x 14||2||70|
|111.295.51||1 x 16||2||40|
|111.295.52||1 x 16||2||50|
|111.295.53||1 x 16||2||60|
|111.295.54||1 x 16||2||70|
|111.295.61||1 x 20||2||40|
|111.295.62||1 x 20||2||50|
|111.295.63||1 x 20||2||60|
|111.295.64||1 x 20||2||70|
|107.070.00||Shackle for pulling unit (to be ordered with the strands)|
Calibration of micro pipes – simple localization of pipe damages
Receiver for Minisonde,
10 kHz, The scope of delivery includes 6 batteries and a bag.
Order No. 009.675.50
Bag for Receiver (ohne Abbildung) Bestell No. 009.675.51
Battery for Receiver (without illustration) Order No. 009.675.52
Minisonde for calibration of micro pipes, Diameter: 6,4mm, Length: 85 mm
Frequency: 10 kHz Order No. 009.675.60
Frequency: 33 kHz Order No. 009.675.61
Battery for Minisonde Order No. 009.675.62
Chain rail Order No. 111.270.00
The chain rail, made from brass, supports the upper and lower drive chain. It is recommended to change the top / bottom rail at the same time.
The drive unit consists of two superimposed conveyor chains and is provided with special rubber profile. Depending on the number and diameter of the Micro ducts appropriate chains are available. The drive chains pull the cable from the drum into the blowing junction block wherefrom it is inserted into the tube by air or water pressure. It is recommended to change the two drive chains at the same time.
|111.272.00||Chain for 7 duct bunch dia. 10 mm|
|111.273.00||Chain for 5/3 duct bunch dia. 10 mm|
|111.269.00||Chain for a single cable|
Cable guide roller, horizontal Order No. 111.224.00
The horizontal cable guide rollers lead and protect the fibre cable by the entry into the Multiflow.
Cable guide roller, vertical Oder No. 111.225.00
The vertical cable guide rollers lead and protect the fibre cable by the entry into the Multiflow.